dhcpcd is an implementation of the DHCP client specified in RFC2131. A DHCP client is useful for connecting your computer to a network which uses DHCP to assign network addresses. dhcpcd strives to be a fully featured, yet very lightweight DHCP client.
This package is known to build and work properly using an LFS-8.1 platform.
Download (HTTP): http://roy.marples.name/downloads/dhcpcd/dhcpcd-6.11.5.tar.xz
Download (FTP): ftp://roy.marples.name/pub/dhcpcd/dhcpcd-6.11.5.tar.xz
Download MD5 sum: 2465624b62c1154f0e89dc69c42c849b
Download size: 196 KB
Estimated disk space required: 2.7 MB
Estimated build time: less than 0.1 SBU
LLVM-4.0.1 (with Clang)
User Notes: http://wiki.linuxfromscratch.org/blfs/wiki/dhcpcd
Install dhcpcd by running the following commands:
./configure --libexecdir=/lib/dhcpcd \
--dbdir=/var/lib/dhcpcd &&
make
This package does not come with a test suite.
Now, as the root user:
make install
--libexecdir=/lib/dhcpcd:
The default /libexec is not
FHS-compliant. Since this directory may need to be available early
in the boot, /usr/libexec cannot be
used either.
--dbdir=/var/lib/dhcpcd:
The default /var/db is not
FHS-compliant
--with-hook=...: You can optionally
install more hooks, for example to install some configuration files
such as ntp.conf. The set of hooks is
in the dhcpcd-hooks directory in the
build tree.
To configure dhcpcd, you need to first
install the network service script, /lib/services/dhcpcd included in the blfs-bootscripts-20170731 package (as
user root):
make install-service-dhcpcd
Whenever dhcpcd configures or shuts down a network interface, it executes hook scripts. For more details about those scripts, see the dhcpcd-run-hooks and dhcpcd man pages.
Finally, as the
root user create the /etc/sysconfig/ifconfig.eth0 configuration file
using the following commands. Adjust appropriately for additional
interfaces:
cat > /etc/sysconfig/ifconfig.eth0 << "EOF"
ONBOOT="yes"
IFACE="eth0"
SERVICE="dhcpcd"
DHCP_START="-b -q <insert appropriate start options here>"
DHCP_STOP="-k <insert additional stop options here>"
EOF
For more information on the appropriate DHCP_START and DHCP_STOP values, examine the man page for
dhcpcd.
![[Note]](../images/note.png)
The default
behavior of dhcpcd sets the hostname and
mtu settings. It also overwrites /etc/resolv.conf and /etc/ntp.conf. These modifications to system
files and settings on system configuration files are done by
hooks which are stored in /lib/dhcpcd/dhcpcd-hooks. Setup dhcpcd by removing or adding
hooks from/to that directory. The execution of hooks can be
disabled by using the --nohook
(-C) command line option or by the
nohook option in the /etc/dhcpcd.conf file.
Review the dhcpcd
man page for switches to add to the DHCP_START value.
Although not
usual, it is possible that you need to configure dhcpcd to use a fixed ip. Here, we give an
example. As the root user create
the /etc/sysconfig/ifconfig.eth0
configuration file using the following commands. Adjust
appropriately for additional interfaces and for the actual ip and
router you need:
cat > /etc/sysconfig/ifconfig.eth0 << "EOF"
ONBOOT="yes"
IFACE="eth0"
SERVICE="dhcpcd"
DHCP_START="-b -q -S ip_address=192.168.0.10/24 -S routers=192.168.0.1"
DHCP_STOP="-k"
EOF
You can either use DNS servers in /etc/resolv.conf from another system, your
preferred servers, or just the example /etc/resolv.conf.head file below as is:
cat > /etc/resolv.conf.head << "EOF"
# OpenDNS servers
nameserver 208.67.222.222
nameserver 208.67.220.220
EOF
Last updated on 2017-08-25 14:22:07 -0700